Polyvinyl chloride (PVC) is a flexible or rigid material that is chemically nonreactive. PVC offers excellent corrosion and weather resistance. It has a high strength-to-weight ratio and is a good electrical and thermal insulator. The most widely used member of the vinyl family, PVC may be cemented, welded, machined, bent and shaped readily.
There are three broad classifications for rigid PVC compounds: Type I, Type II, and CPVC. Type II and CPVC offer better heat and chemical resistance as well as greater impact resistance. These materials are considered “unplasticized” (rigid) because they are less flexible than the plasticized formulations. Type I, II, and CPVC are normally available in rod, sheet, slab, pipe, tubular bar, fittings and valves. “Plasticized” PVC is available in sheet, film, fittings, flexible tubing, and pipe.
The properties of PVC can be varied by the addition of fillers, plasticizers, stabilizers and colorants. Contact an Emco Industrial Plastics representative who can help you choose the correct material to meet the needs of your applications.
Emco Industrial Plastics doesn’t claim to represent all of the manufacturers or trade name products listed. This list is intended as a guide of typical materials available for purchase from Emco Industrial Plastics, Inc. For additional information, contact an Emco Industrial Plastics representative by filling out the form below.
Contact us today for your fabrication and machining needs!
Request Fabrication/Machining ServicesGeneric Name
Polyvinyl Chloride, Type II
Available In
Sheet
Start Your Quote
Send us a message:
*Required Fields
| Type | Size | Length | Color |
|---|---|---|---|
| Sheet | 1/8″ – 1″ TH | Lt. Grey, Dk. Grey, White |
Give us your cut-to-size dimensions. We will precision-cut these plastics to your exact size. Additional sizes and colors available upon request.
| Physical Properties | Units | ASTM | Results |
|---|---|---|---|
| Density | lb/in³ | D792 | 0.0488 |
| Water Absorption, 24 hrs | % | D570 | 0.05 – 0.16 |
| Mechanical Properties | Units | ASTM | Results |
|---|---|---|---|
| Tensile Strength @yield | psi | D638 | 6,050 – 7,500 |
| Tensile Modulus | psi | D638 | 345,000 – 396,000 |
| Tensile Elongation @Break | % | D638 | 145 |
| Flexural Strength | psi | D790 | 10000 |
| Flexural Modulus | psi | D790 | 400000 |
| Hardness, Rockwell R | D785 | 106 | |
| IZOD Impact Strength Notched | ft-lb/in | D256 | 14 – 18 |
| Thermal Properties | Units | ASTM | Results |
|---|---|---|---|
| Heat Deflection Temp at 66 psi | °F | D648 | 165 – 179 |
| Heat Deflection Temp at 264 psi | °F | 158 – 176 | |
| Melting Temperature | °F | D3418 | 162 – 181 |
| Flammability Rating | UL94 | V – O |
| Electrical Properties | Units | ASTM | Results |
|---|---|---|---|
| Dielectric Strength, 1/8″ th. | V/mil | D149 | 1638 |
| Dielectric Constant @60HZ | D150 | 3.03 | |
| Dissipation Factor @ 60 Hz | D150 | 0.0083 | |
| Volume Resistivity | ohm-cm | D257 | >10¹⁵ |
NOTE: The property values presented above are typical values intended for reference and comparison purposes only. They should NOT be used as a basis for design specifications or quality control. Contact us for manufacturers’ complete material property datasheets. All values at 73°F (23°C) unless otherwise noted.
NOTE: Several grades of this material are available. For additional information regarding this plastic, contact your Emco Industrial Plastics representative or call 973-862-4148.