DisplaysResourcesSpecialsGalleryGet a Quote

Extruded Nylon 6/6 (polyhexamethylene adiptimide) is a moldable and extrudeable general-purpose nylon. Like Cast Nylon 6, it has good mechanical properties and wear resistance. Nylon 6/6 has a much higher melting point, better mechanical properties due to greater hardness, and lower water absorption than cast nylon. Because of its excellent balance of strength, ductility and heat resistance, nylon 6/6 is an outstanding candidate for metal replacement applications. Nylon 6/6 is very easy to process with a very wide process window. This allows it to be used for everything from complex, thin walled components to large thick walled housings. Unmodified nylon 6/6 is stocked in both natural and black; other colors are available on a custom basis. Unmodified nylon 6/6 is FDA, USDA, NSF and 3-A Dairy compliant.

Brand Names

  • Nylon 101
  • Ensilon®
  • Polypenco® 101
  • Sustamid® G66
  • Unipa®
  • Zytel® ST801

Emco Industrial Plastics doesn’t claim to represent all of the manufacturers or trade name products listed. This list is intended as a guide of typical materials available for purchase from Emco Industrial Plastics, Inc. For additional information, contact an Emco Industrial Plastics representative by filling out the form below.

Do you need Fabrication or Machining for Nylon Extruded Type 6/6 Unfilled?

Contact us today for your fabrication and machining needs!

Request Fabrication/Machining Services
At a Glance

Generic Name
Polyamide

Available In
Sheet, Rod, Tube, Other

Certifications
FDA Compliant, MIL-P-19904

Start Your Quote

Send us a message:

*Required Fields

Gallery

Technical Information

Stock Products Properties Applications Advantages Grades

Stock Products

TypeSizeLengthColor
Sheet 1/32″ – 4″ TH Standard 12″, 24″ x 48″; 24″ x 96″; CTS Natural, Black
Rod 3/16″ – 8″DIA; 1/4″ – 1″ sq.; 3/16″ – 1″ hex Standard foot lengths, CTS Natural, Black
Tube 2″ – 14″ OD Standard foot lengths, CTS Natural
Other Balls 1/8″ – 3″ DIA Natural; Natural Screws 3/16″ – 2″ L in various heads and thread sizes Natural

Give us your cut-to-size dimensions. We will precision-cut these plastics to your exact size. Additional sizes and colors available upon request.

Properties

Physical PropertiesUnitsASTMResults
Density lb/in3 D792 0.042
Water Absorption, 24 hrs % D570 0.3
Mechanical PropertiesUnitsASTMResults
Tensile Strength psi D638 11500
Tensile Modulus psi D638 425000
Tensile Elongation @Break % D638 50
Flexural Strength psi D790 15000
Flexural Modulus psi 400000 450000
Compressive Strength psi D695 12500
Compressive Modulus psi D695 420000
Hardness, Rockwell R D785 115
IZOD Impact Strength Notched ft-lb/in D256 0.6
Thermal PropertiesUnitsASTMResults
Coefficient of Linear Thermal Expansion in./in./°F D256 5.5 x 10-5
Heat Deflection Temp at 264 psi °F 200
Melting Temperature °F D3418 500
Max Operating Temp °F 210
Thermal Conductivity BTU-in/ft2-hr-°F C177 1.7
Flammability Rating UL94 V-2
Electrical PropertiesUnitsASTMResults
Dielectric Strength V/mil D149 400, 1/8″ th
Dielectric Constant D150 3.6
Dissipation Factor @ 60 Hz D150 0.02
Volume Resistivity, 50% RH ohm-cm D257 >10^13
NOTE: The property values presented above are typical values intended for reference and comparison purposes only. They should NOT be used as a basis for design specifications or quality control. Contact us for manufacturers’ complete material property datasheets. All values at 73°F (23°C) unless otherwise noted.

Applications

  • Machine parts
  • Bearings, bushings, gears
  • Valve Seats and Wear Surfaces
  • Rollers
  • Guides
  • Thin walled technical components

Advantages

  • Good electrical insulator
  • High chemical resistance
  • Good wear and abrasion resistance
  • Easily fabricated into precision parts using standard metalworking equipment
  • USDA and FDA compliant (natural only)
  • Vibration and peening resistance
  • Good impact resistance

Grades

  • Extruded (Type 6), Unfilled
  • Extruded (Type 6), Unfilled, Heat Stabilized
  • Extruded (Type 6), Oil Filled
  • Extruded (Type 6), Moly2 Filled
  • Extruded (Type 6), Glass Filled
Copyright © 2016 - 2017 Emco Industrial Plastics